Vanguard VE36L User Manual

®For more information, visit www.desatech.comPLEASE READ THIS MANUAL BEFORE INSTALLING AND USING APPLIANCE. WARNING: If the information in this m

www.desatech.com115121-01B10ACCESSORy INSTALLATIONContinued5. Insert brick panel, beveled edge first, through rebox opening. Tilt and angle top

www.desatech.com115121-01B 11ACCESSORy INSTALLATIONContinued7. Remove blower/heater assembly with 4 screws from packaging. Blower is pre-wired

www.desatech.com115121-01B12ACCESSORy INSTALLATIONContinued15. Connect red heater wire to terminal marked 'L-4' on heater power switch

www.desatech.com115121-01B 13TROUBLESHOOTINgNote: Before troubleshooting system, make sure power to circuit from breaker or fuse panel is turned ON.Th

www.desatech.com115121-01B14WIRINg DIAgRAMYELLOW LAMPWHTHARNESS 4" BLKHEATERPOWERFRONT HARNESS TO LAMP CIRCUITRED LAMPSPLICE CONNECTION MALE C

www.desatech.com115121-01B 15MAINTENANCE WARNING: Disconnect power before attempting any maintenance or cleaning to re-duce the risk of re,

www.desatech.com115121-01B165. Rotate control door up into control com-partment and slide on end into side of compartment.6. Tilt out one end

www.desatech.com115121-01B 17ACCESSING IMAGING UNITThe imaging unit can be accessed from inside replace for servicing as follows:1. Remove glass d

www.desatech.com115121-01B18SERVICING FAN BLOWERTo remove fan blower:1. Follow instructions under Accessing Imag-ing Unit, page 17.2. Remove 3 light

www.desatech.com115121-01B 198"7"3 1/2"1 1/2"Figure 38 - Locating Flame PennantsFlame CordFlame PennantFlame SpacerMAINTENANCECont

www.desatech.com115121-01B2SAFETy INFORMATIONTABLE OF CONTENTSSafety Information ... 2Product Specication

www.desatech.com115121-01B20Figure 39 - Replacing Fixtures (Shown without FIrebox for Clarity)Screws and WashersHangerScrewsReective RibbonLamp Fixtu

www.desatech.com115121-01B 21MAINTENANCEContinued14. Center log bed over opening between viewing panel screen and grate.15. Cover remaining heart

www.desatech.com115121-01B22TECHNICAL SERVICEYou may have further questions about instal-lation, operation or troubleshooting. If so, contact DES

www.desatech.com115121-01B 23ACCESSORIESPurchase these firebox accessories from your local dealer. If they can not supply these accessories, call

www.desatech.com115121-01B24ILLUSTRATED PARTS BREAkDOWNMODELS VE32L, VE32LB, VE32LH, VE32LBH, VE36L, VE36LB, VE36LH AND VE36LBH12334567889101011111212

www.desatech.com115121-01B 25PARTS LISTThis list contains replaceable parts used in your replace. When ordering parts, follow the instructions listed

www.desatech.com115121-01B26ILLUSTRATED PARTS BREAkDOWNIMAGING UNIT AND CONTROL PANEL FOR MODELS VE32L, VE32LB, VE32LH, VE32LBH, VE36L, VE36LB, VE36LH

www.desatech.com115121-01B 27KEY NO. PART NO. DESCRIPTION QTY.1 112734-01 Flame Power Harness • • 12 112734-02 Fan Power Harness • • 13 112469-01 Lam

2701 Industrial DriveP.O. Box 90004Bowling Green, KY 42102-9004www.desatech.com1-866-672-6040115121-01Rev. B11/06NOT A UPCWARRANTy INFORMATIONkEEP THI

www.desatech.com115121-01B 3PRODUCT SPECIFICATIONVE32 = 155/8"VE36 = 17"VE32 = 161/4"VE36 = 175/8"VE32 = 221/4"VE36 = 241/4&q

www.desatech.com115121-01B4INSTALLATION CLEARANCESMinimum clearances to combustible construc-tion are:• Top, Back and Sides of Recessed Cabinet .

www.desatech.com115121-01B 5INSTALLATIONContinued5. Snap assembled trim kit onto shoulder screws around face to lock replace into mantel facing

www.desatech.com115121-01B6ELECTRICAL INSTALLATION WARNING: Any electrical re-wiring of this appliance must be done by a qualied electrician. This wi

www.desatech.com115121-01B 7INSTALLATIONContinuedLAMPS AND LAVA ROCKBefore operating replace, lamp bulbs must be inspected and lava rock may be added

www.desatech.com115121-01B8ACCESSORy INSTALLATIONOPTIONAL GLASS DOORSModels VE36L and VE32L will accept bifold glass doors that are fully operable or

www.desatech.com115121-01B 9Removing Bifold Glass DoorsBifold doors may be removed for replacing or cleaning.1. Partially open each door and pr